How To Install Motocross Graphics

Motocross graphics not only enhance the visual appeal of your bike but also provide protection against scratches, dirt and other elements. Installing motocross graphics may seem like a daunting task, but with the right guidance and approach, you can achieve professional-looking results. 

If you’ve ever wondered how to install motocross graphics flawlessly, then you’re in luck! We’ve created a step-by-step guide that’ll walk you through the process of installing motocross graphics. 

How to apply motocross graphics

Follow the steps below to ensure a smooth and successful application of motocross graphics. 

  • Gather the necessary tools

Before you begin, make sure you have the following tools ready:

  • Heat gun or hairdryer
  • Isopropyl alcohol or a mild detergent
  • Clean lint-free cloth
  • Squeegee or plastic card
  • Utility knife or razor blade
  • Masking tape
  • Prepare the surface

Proper preparation is crucial for a successful installation. To prepare the surface for installing your motocross graphics, be sure to clean the bike's plastic thoroughly using isopropyl alcohol or a mild detergent to remove any dirt, grease or wax. Remember to dry the surface completely with a clean lint-free cloth to ensure a smooth adhesion.

  • Aligning and applying the graphics

To perfectly apply the motocross graphics, start by positioning the graphics on the desired area of the bike. Use masking tape to hold the graphics in place temporarily. Then take a step back and evaluate the alignment of the graphics. Make any necessary adjustments to ensure a precise fit and symmetrical look.

Once you’re satisfied with the alignment, peel off a small section of the backing paper from the graphics, exposing the adhesive side. Using a heat gun or hairdryer on a low setting, warm up the adhesive side of the graphics and the corresponding area on the bike's plastic. This will make the adhesive more pliable and improve adhesion.

Carefully place the exposed adhesive section onto the plastic, aligning it with the intended position. As you apply the graphics, use a squeegee or plastic card to smooth out any air bubbles and ensure proper adhesion. Work from the centre towards the edges, applying even pressure.

Repeat the process, peeling off small sections of the backing paper at a time and applying the graphics until the entire design is in place. If you encounter any stubborn air bubbles, use a pin or needle to prick them and then smooth them out with the squeegee.

  • Trimming and final touches 

Once the graphics are applied, use a utility knife or razor blade to trim any excess material carefully. Take your time and make precise cuts along the edges for a clean look. After trimming, go over the entire graphic with a heat gun or hairdryer once again. This helps the adhesive bond securely to the plastic and eliminates any remaining air bubbles.

Use the squeegee or plastic card to ensure firm adhesion and remove any remaining air bubbles. Finally, step back and inspect for any imperfections. Smooth out any wrinkles or bubbles, if necessary.

Install motocross graphics with ease

By following these step-by-step instructions, you can confidently install motocross graphics on your bike and achieve professional-looking results. Remember to take your time, pay attention to the alignment and use the right tools for the job. With a little practice and patience, you'll be able to transform your bike's appearance and protect it with high-quality motocross graphics.

How to increase the longevity of your motocross graphics

To increase the longevity of your motocross graphics, follow these simple tips:

  • Clean the graphics regularly with mild soap and water.
  • Avoid using harsh chemicals or abrasive materials that can damage the graphics.
  • Avoid direct exposure to sunlight for extended periods.
  • Use a heat gun or hairdryer on a low setting to reactivate the adhesive if any edges begin to lift.
  • Be cautious when pressure washing your bike, keeping the nozzle at a safe distance from the graphics.
  • Store your bike in a cool, dry place when not in use to prevent fading or peeling.

Get your motocross graphics supplies from Creative Graphic Supplies!

At Creative Graphic Supplies (CGS), we specialise in powersports graphics and offer a wide range of printing, laminating and heat transfer materials and accessories. With more than 80 years of experience, we have created a team that’s dedicated to providing exceptional products to enhance your motocross experience. Visit our website to explore our motocross graphic supplies and take your bike's aesthetics to the next level.

For all your motocross graphic needs, remember to only trust CGS!

Index Previous Next


© Copyright Creative Graphic Supplies Pty Ltd - Site map
Phone: 07 3890 5414 Brisbane City Australia

Designed By TidyCommerce

Top